Beschrijving
Geslepen precisietandwielrekken
Ground precision rack solutions for demanding positioning and repeatability requirements.
Direct answer
Ground-finished tooth option; target quality/tolerance must be confirmed from drawing. Final dimensions, material, treatment, finish and inspection scope are confirmed for the ordered configuration.
Selection variables
Pitch system
Module, DP or CP must match the mating pinion.
Pressure angle
Confirm from the machine drawing or existing tooth system.
Rack geometry
Body section, length, mounting holes and end features.
Accuracy
State drawing tolerance or target gear quality class.
Material & treatment
Define grade, treatment and hardness when they are design requirements.
Duty
Travel, speed, acceleration, load/force, cycle and environment.
Technical specification table
| Specificatie | Project-/bestelvereisten |
|---|---|
| Product family | Ground precision |
| Tooth pitch | Project-specific module / DP / CP; verify from drawing/RFQ. |
| Pressure angle | Confirm for ordered configuration. |
| Helix data | Confirm where applicable. |
| Rack length / section | Drawing- and project-specific. |
| Rack body / holes | Drawing-defined dimensions and mounting pattern. |
| Materiaal | Specified by drawing and duty; final grade confirmed with quotation. |
| Heat treatment / hardness | Specified by required wear/load behavior and drawing. |
| Tooth finish | Cut / hardened / ground as ordered and technically applicable. |
| Quality / tolerance | Target DIN/ISO/AGMA or drawing tolerance to be stated by buyer. |
| Pinion interface | Matching tooth system; pinion bore/shaft/hub is project-specific. |
| Quantity | Required for quotation and process planning. |
Rack and pinion must be treated as one tooth system
A rack cannot be selected independently from the mating pinion. Confirm the same pitch system and pressure angle, then check helix geometry where applicable. Replacement work should also verify wear and any machine-side geometry that could change the installed mesh.
Long travel needs section alignment
When the axis uses several rack sections, specify the segment length, joint relationship and mounting datum. Installation error can overwhelm the nominal rack accuracy if the machine surface and joints are not controlled.
Material, heat treatment and finish
The process route is selected from the drawing and the performance target. Do not assume a material or hardness from another supplier’s catalogue is automatically the right specification for your machine.
Material grade
State the required alloy/steel grade or allow project-specific selection review.
Warmtebehandeling
Define the target hardening/treatment condition if required.
Tooth finish
Cut, hardened or ground tooth finish according to the requested configuration.
Protection
Specify corrosion protection only when the environment requires it.
Typical applications
CNC-bewerkingsgereedschap
Voedingssystemen met lange as, waarbij stijfheid, gecontroleerde speling en herhaalbare installatie van belang zijn.
Robot 7e-as rupsbanden
Tandwieloverbrenging voor een groter werkbereik van de robot en transportassen.
Lasersnijmachines
Hoogfrequente portaalbeweging die profiteert van een zuivere, herhaalbare lineaire aandrijfgeometrie.
Zwaar transport met portaalkranen en kraanwagens
Robuuste tandheugelaandrijvingen voor lange slagen, grote bewegende massa's en projectspecifieke gebruikscycli.
Automatisering van materiaalverwerking
Transfer-, shuttle- en positioneringssystemen waarbij lange verplaatsingsafstanden tandwielaandrijvingen praktisch maken.
RFQ checklist
Attach the rack drawing and send the mating pinion information, quantity and machine duty. For a replacement, include photographs and any markings as secondary identification aids.
Veelgestelde vragen
Can this product be made to a drawing?
Yes, drawing-based projects can be reviewed. Final feasibility depends on dimensions, tooth geometry, process, quantity and inspection requirements.
Can you guarantee a quality class from this page?
No. The exact class/tolerance is confirmed for the ordered configuration and should appear on the drawing or quotation.
Can the mating pinion be quoted together?
Yes. Quoting both parts helps keep the tooth system and interface controlled.
Send the rack and pinion data as one RFQ.
Vermeld het type tandheugel, het steeksysteem, de drukhoek, de vereiste lengte, de gegevens van het bijbehorende rondsel, de beoogde nauwkeurigheid of tolerantie, de bedrijfsbelasting en de hoeveelheid. Een tekening is de snelste manier om onduidelijkheden weg te nemen.
