Drawing revision
Use one approved revision with all rack and pinion interfaces controlled.
MANUFACTURING & QUALITY
Manufacturing & Quality for Gear Rack Projects
The manufacturing route should be chosen from the drawing and performance requirement. EVER POWER coordinates machining, heat-treatment, tooth finishing and inspection for the ordered configuration rather than publishing unsupported one-size-fits-all process claims.
Drawing ControlProcess PlanningInspeksi
From drawing to inspection
A rack project moves through a controlled sequence. The exact steps vary by material, heat treatment, tooth finish and required tolerance.
Process planning inputs
Bahan
Specify grade and condition where material is a design requirement.
Perlakuan panas
State target hardness, case requirement or other acceptance criteria where applicable.
Tooth finish
Cut, hardened or ground tooth requirements must match the accuracy and duty target.
Datum & machining
Mounting faces, hole patterns and end features need clear references.
Inspection scope
Define what must be measured and which documents are required with the order.
Inspection follows the drawing
Useful inspection only exists when the drawing defines the requirement. Dimensional checks can cover the rack body, mounting interface and specified tooth-related tolerances. Material, heat-treatment or hardness records can be discussed when required by the order.
Typical manufacturing variables
| Spesifikasi | Persyaratan proyek/pemesanan |
|---|---|
| Rack geometry | Spur or helical; module/DP/CP; pressure angle; rack body section. |
| Machining | Tooth cutting plus project-specific hole/end/body machining. |
| Perlakuan panas | As specified for the ordered material and wear/load requirement. |
| Tooth finishing | Project-specific cut/hardened/ground requirement. |
| Surface protection | Only when called for by drawing or environment. |
| Inspeksi | Dimensional and tooth-related checks defined by drawing and order. |
Precision is a system property
Rack quality
Pitch and tooth geometry affect the linear tooth path.
Pinion quality
The mating pinion contributes its own errors and runout.
Mounting datum
An inaccurate machine surface can dominate the installed result.
Backlash setting
Mesh adjustment changes reversal behavior and load sharing.
Gearbox & bearings
Torsional stiffness and shaft support influence the complete axis.
Pelumasan
Wear behavior depends on the actual duty and maintenance method.
Long rack runs need installation discipline
Segmented racks can extend travel without making one impossible-to-handle component. The benefit depends on controlled section alignment and joint continuity. Keep datum surfaces clean, use the defined alignment method and verify engagement along the full travel.
Documentation is agreed with the order
Do not assume a certificate or report is included simply because a product page mentions inspection. Tell us what the project needs—approved drawing, dimensional report, material document, hardness record or other agreed deliverable—so it can be included in the commercial review.
What we do not publish without evidence
We do not publish invented plant size, machine counts, market share, named end customers, unsupported certifications or guaranteed accuracy ranges. Project-specific capability is confirmed from the drawing and process review.
Use the RFQ to define the acceptance basis
MOQFleksibel berdasarkan jenis produk dan nilai total pesanan.
SampelPelanggan baru dapat memesan 1-5 buah jika suku cadang dan prosesnya sesuai.
Pesanan campurBerbagai model rack, pinion, atau model terkait lainnya dapat dikombinasikan jika total nilai pesanan sekitar USD 1.500 atau lebih.
Pesanan kecilPemesanan mulai dari 1-2 buah dapat dibicarakan, biasanya dengan biaya satuan yang lebih tinggi.
PengirimanKomponen standar: 10-25 hari kerja. Komponen khusus: 20-45 hari kerja. Peralatan proyek: 45-120 hari kerja.
Syarat perdaganganEXW, FOB, CIF, dan DAP umumnya didukung. FCA, CFR, CPT, CIP, dan DDP dapat dibahas berdasarkan kasus per kasus.
Pertanyaan yang sering diajukan
Can inspection reports be requested?
Yes. State the required measurements and report format at the RFQ stage so the scope can be confirmed.
Do all racks use the same heat treatment?
No. Treatment depends on material, tooth finish, wear/load requirement and drawing specification.
Can an existing supplier specification be copied directly?
We can review a drawing or cross-reference requirement, but third-party proprietary data should not be assumed to define an EVER POWER part without technical confirmation.
Permintaan Penawaran (RFQ)
Put the process and inspection requirement on the RFQ before price is fixed.
Sertakan tipe rak, sistem pitch, sudut tekanan, panjang yang dibutuhkan, data pinion pasangannya, akurasi atau toleransi target, tugas pengoperasian, dan kuantitas. Gambar adalah cara tercepat untuk menghilangkan ambiguitas.
MOQFleksibel berdasarkan jenis produk dan nilai total pesanan.
SampelPelanggan baru dapat memesan 1-5 buah jika suku cadang dan prosesnya sesuai.
Pesanan campurBerbagai model rack, pinion, atau model terkait lainnya dapat dikombinasikan jika total nilai pesanan sekitar USD 1.500 atau lebih.
Pesanan kecilPemesanan mulai dari 1-2 buah dapat dibicarakan, biasanya dengan biaya satuan yang lebih tinggi.
PengirimanKomponen standar: 10-25 hari kerja. Komponen khusus: 20-45 hari kerja. Peralatan proyek: 45-120 hari kerja.
Syarat perdaganganEXW, FOB, CIF, dan DAP umumnya didukung. FCA, CFR, CPT, CIP, dan DDP dapat dibahas berdasarkan kasus per kasus.
